JavaScript seems to be disabled in your browser.

You must have JavaScript enabled in your browser to utilize the functionality of this website. Click here for instructions on enabling javascript in your browser.

4 in. Pellet Stove Chimney

 VP Pellet Pipe™ 

Selkirk® gives you the safe, efficient, and cost-effective venting system that\'s engineered precisely for pellet burning stoves. Model VP
Pellet Pipe has been tested and listed by Underwriters\' Laboratories, Inc., in accordance with UL®-641 Standard for Low
Temperature Venting Systems, as well as the applicable requirements from UL®-103 Standard for Residential Type and Building
Heating Appliance Chimneys. VP Pellet Pipe, when installed according to Selkirk’s® installation instructions, complies with
National Safety Standards, such as NFPA -211. The system is rated for flue temperatures up to 570°F.

• Available in 3" and 4" diameters
• Full line of fittings and full range of pipe lengths increase installation flexibility
• Proven coupling joint connects in seconds to assure joint integrity
• Gasketed joint design
• Painted pipe lengths available for interior use
• Double wall design with 1/4” airspace
• Inner wall 304 stainless steel, outer wall paintable galvanized
• Rolled-over male end eliminates sharp edges
• 1" clearance to combustibles
• Removable tee cap for inspection and cleaning
• Internal spacing bead assures uniform insulating airspace between pipe walls

Installation Instructions

Special Note: Sand Hill Also Carries A Full Line Of Pellet Products:

  • Rods & Brushes
  • Trim Collars
  • Fire Starter
  • Black Pipe
  • Ventinox VG Liner

 

4'' Thick Wall Thimble for Selkirk Pellet Chimney

4'' Thick Wall Thimble for Selkirk Pellet Chimney

A Wall Thimble must be used for all through-the-wall installations involving combustible construction. The thick wall thimble is designed to…


 $105.89 

View

Model: 2396

4" Ultimate PelletPipe™  90° Elbow

4" Ultimate PelletPipe™ 90° Elbow

This 90° elbow is used to offset around an obstruction.
It is UL listed to standard UL641 as a Type L…


 $67.59 

View

Model: 2217

4'' x 12'' Selkirk Pellet Chimney

4'' x 12'' Selkirk Pellet Chimney

Each flue gas carrying section of the pellet pipe is designed with a male and female end coupling. To join…


 $41.89 

View

Model: 2318

4'' x 24'' Selkirk Pellet Chimney

4'' x 24'' Selkirk Pellet Chimney

Each flue gas carrying section of the pellet pipe is designed with a male and female end coupling. To join…


 $66.09 

View

Model: 2314

4'' x 36'' Selkirk Pellet Chimney

4'' x 36'' Selkirk Pellet Chimney

Each flue gas carrying section of the pellet pipe is designed with a male and female end coupling. To join…


 $92.69 

View

Model: 2310

4'' x 60'' Selkirk Pellet Chimney

4'' x 60'' Selkirk Pellet Chimney

Each flue gas carrying section of the pellet pipe is designed with a male and female end coupling. To join…


 $122.09 

View

Model: 2302

3'' & 4'' Pellet Tee Support for Selkirk Pellet Chimney

3'' & 4'' Pellet Tee Support for Selkirk Pellet Chimney

The tee support is optional and should not be installed until the wall thimble installation has been completed. If the…


 $30.29 

View

Model: 2348

4'' 45 Degree Elbow for Selkirk Pellet Chimney

4'' 45 Degree Elbow for Selkirk Pellet Chimney

Adjustable 45 degree elbows are available for use in accommodating unusual offsets and configurations. These optional accessories are designed with…


 $79.49 

View

Model: 2326

4'' 90 Degree Elbow for Selkirk Pellet Chimney

4'' 90 Degree Elbow for Selkirk Pellet Chimney

Adjustable 90 degree elbows are available for use in accommodating unusual offsets and configurations. These optional accessories are designed with…


 $111.29 

View

Model: 2330

4'' Adjustable Flashing 1/12-6/12 for Selkirk Pellet Chimney

4'' Adjustable Flashing 1/12-6/12 for Selkirk Pellet Chimney

Roof flashings are used to provide a transition at the roof through which the vent will pass and to protect…


 $50.39 

View

Model: 2338

4'' Black Trim Plate for Selkirk Pellet Chimney

4'' Black Trim Plate for Selkirk Pellet Chimney

The trim plate is used to finish off the bottom (ceiling) side of a floor/ceiling penetration. Install the trim plate…


 $30.09 

View

Model: 2366

4'' Ceiling Support/Firestop for Selkirk Pellet Chimney

4'' Ceiling Support/Firestop for Selkirk Pellet Chimney

Used to support pipe from the ceiling joist. Maintains clearance to combustibles.…


 $100.49 

View

Model: 2346

4'' Homeguard Shield for Selkirk Pellet Chimney

4'' Homeguard Shield for Selkirk Pellet Chimney

The galvanized plate is used to finish off the exterior of a wall penetration. Plate is 12" square.…


 $30.59 

View

Model: 2370

4'' Horizontal Chimney Cap for Selkirk Pellet Chimney

4'' Horizontal Chimney Cap for Selkirk Pellet Chimney

The horizontal termination cap is designed specifically for use on installations in which the vent terminates in a horizontal orientation…


 $98.19 

View

Model: 2386

4'' Horizontal Exit Cap for Selkirk Pellet Chimney

4'' Horizontal Exit Cap for Selkirk Pellet Chimney

4'' pellet chimney cap for exhausting straight out horizontally. Useful for applications where flue exhaust cannot be diverted to sides.…


 $74.89 

View

Model: 2392

4'' Pellet Tee with Cap for Selkirk Pellet Chimney

4'' Pellet Tee with Cap for Selkirk Pellet Chimney

Tee sections are designed for use in changing the orientation of the vent from horizontal to vertical and to facilitate…


 $125.59 

View

Model: 2354

4'' Pipe Connector for Selkirk Pellet Chimney

4'' Pipe Connector for Selkirk Pellet Chimney

The vent connector is a (“starter section”) fitting used to connect the flue collar of the appliance of the pellet…


 $35.79 

View

Model: 2374

4'' Storm Collar for Selkirk Pellet Chimney

4'' Storm Collar for Selkirk Pellet Chimney

The storm collar is used at the top of each flashing to assist in shedding water from the assembly. Inside…


 $7.99 

View

Model: 2342

4'' Tall Cone Flashing for Selkirk Pellet Chimney

4'' Tall Cone Flashing for Selkirk Pellet Chimney

Roof flashings are used to provide a transition at the roof through which the vent will pass and to protect…


 $35.99 

View

Model: 2334

4'' Vertical Chimney Cap for Selkirk Pellet Chimney

4'' Vertical Chimney Cap for Selkirk Pellet Chimney

The vertical termination cap is intended for use in all installations in which the vent terminates in a vertical orientation.…


 $60.29 

View

Model: 2382

Result Pages: